Recovery information controller output as device chip card

Recovery information controller output as device chip card
In modern photographic equipment, memory cards are usually used to store captured photos and video information. Among digital cameras, phones, tablets, video recorders, and other devices, cards are the most widely used. Use of professional SLR cameras. The memory card is designed for use in photographic equipment, and only memory cards in the format are used in the equipment.
Any memory card is a storage medium, somewhat similar to a flash drive. The reasons for losing data from this medium may be different, divided into software, machinery and hardware. Software reasons that cause data loss include memory card overflow, accidental deletion or formatting, and virus attacks. When the controller fails or there are many bad storage units on the microcircuit, hardware reasons should be considered. If the memory card is logically damaged, you can use the utility to independently restore Stanfield the information. If the memory card of the camera is mechanically damaged, and thus the information recorded on the camera, it is difficult to recover, because in this case, the printed circuit board will suffer damage and the contact with the microcircuit will break. The best option to solve the problem of recovering data when the memory card is mechanically damaged is to contact an expert.
The first step in determining the failure and the possibility of recovering information from the memory card is diagnosis. The diagnosis task will mainly be to determine the access rights to the logical sectors of the map and the correctness of reading. In our time, they are the most common because they are used in most modern mainstream devices. These are smartphones, tablets, video recorders and cameras. They are everywhere. People often blindly believe in their reliability and store any valuable information in it. At the same time, they don't even care (at least occasionally) to create a backup.

But it is precisely because of their universality and bulkiness that memory cards are the least reliable. Moreover, due to their miniature size, the design of such cards is only done in an integral form. The whole is a drive in which the controller and memory chip are made of a crystal. Therefore, if the controller of this memory card fails, the only way to recover the data is to solder it directly to the terminals of the memory chip under the microscope. Purchased a similar repairable memory card. Peel a layer of varnish from it to reach the memory pins, and then solder a wire to them (usually a wire with a diameter of 0.6). There are usually 15 or more pins, so there is one pin: a schematic diagram of one pin responsible, and then the pins of the faulty card are soldered to a special adapter under the microscope.
This process is very laborious, so unlike other size cards, it takes more time to recover data from a memory card. It consists of a printed multilayer board with an interface for connecting devices, controllers and storage chips that store all data. The memory reads and decodes the read information. The reading algorithm depends on the drive controller. Recovering information from a faulty memory card at home is difficult because it requires special equipment, programs, and utilities. Recovering data from the memory card depends on the type of failure, and can be recovered by logical scanning or from the memory chip (if available).

Most of them lack a memory chip control controller. The process of restoring information from a memory card is not much different. The only condition is the existence of a dedicated adapter. The device controller is located near the interface connector inside the card box; the microcircuit is soldered below. Recover data from memory cards and cards. When the file structure is violated or the operation fails, the utility will be used. If the controller fails, the information can be recovered directly from the microcircuit. In this type of card, an overall form of execution is often found. The whole is a drive in which the controller and memory chip are made of a crystal. Therefore, if the controller dies in this memory card, the only way to recover the data is to solder it directly to the pins of the memory microcircuit under a microscope, and then use a reader to read the data. This process is very laborious, and the cost of restoring such data starts at 25,000 rubles. Used to store data in digital cameras. The metal box of the card contains a controller and several memory chips. The unique feature of such devices is their resistance to mechanical stress. Therefore, the problem of recovering data from compact flash memory rarely occurs. When using a memory card, some rules must be followed to avoid loss of information. Before removing the memory card from the card reader, you must disconnect it in the operating system.

In order to minimize the risk of information loss, you can regularly check the operating system for viruses.
The fewer times the card is removed from the camera, the less likely it is to damage the card. Therefore, you need to use a cable to copy the photos and videos in the camera to the computer.
When deleting unnecessary files, take extra care and make a backup.

If you find that the memory card is malfunctioning, please contact an expert.
Kingston Technology announced the start of sales of the latest compact flash drives 3. Can This USB Stick Resurrect Your Old PC?